RoaringBox/Konfiguration: Unterschied zwischen den Versionen
Aus UUGRN
K (BEGIN{}) |
(→/etc/default/roaraudio: aktuelle config) |
||
Zeile 5: | Zeile 5: | ||
=== /etc/default/mini-httpd === | === /etc/default/mini-httpd === | ||
=== /etc/default/roaraudio === | === /etc/default/roaraudio === | ||
+ | <pre> | ||
+ | #RoarAudio Configuration | ||
+ | |||
+ | # --- [ General Options ]--- | ||
+ | |||
+ | # Start roard? YES or NO: | ||
+ | ROARD='YES' | ||
+ | |||
+ | # Additionl Options to pass to roard, should normally be empty | ||
+ | ROARD_OPTS='--new-sock -u -b /tmp/roar' | ||
+ | |||
+ | # Should we run roard in realtime mode: | ||
+ | # NO - Don't run in realtime mode | ||
+ | # YES - Run in realtime mode | ||
+ | # DOUBLE - Try to run in a 'very realtime mode' | ||
+ | ROARD_REALTIME='YES' | ||
+ | |||
+ | # PIDFile for roard: | ||
+ | # Default is enabled at /var/run/roard.pid | ||
+ | # Set to empty string to disable. | ||
+ | PIDFILE='/var/run/roard.pid' | ||
+ | |||
+ | # Location of roard: | ||
+ | # This is a human readable location of the roard used | ||
+ | # for Zero Conf locating of a RoarAudio server on the | ||
+ | # Network. To use Zero Conf enable SLP (see below). | ||
+ | #ROARD_LOCATION='' | ||
+ | |||
+ | # Default location for roard: | ||
+ | # Set this to a remote address and disable local roard | ||
+ | # to run a network only setup. | ||
+ | # ROARAUDIO_DEFAULT_SOCKET='server.local' | ||
+ | |||
+ | # --- [ Network ] --- | ||
+ | |||
+ | # Listening socket's address family: | ||
+ | # UNIX - Local connections only | ||
+ | # TCP - Connections via TCP/IP | ||
+ | # DECnet - Connections via DECnet | ||
+ | ROARD_AF='TCP' | ||
+ | |||
+ | # Socket to listen on (UNIX): | ||
+ | #ROARD_SOCKET='/tmp/roar' | ||
+ | |||
+ | # Port to listen on (TCP): | ||
+ | # ROARD_PORT=16002 | ||
+ | |||
+ | # Host/Nodename to listen on (TCP, DECnet): | ||
+ | # use a value of '0.0.0.0' to listen publicly for TCP. | ||
+ | ROARD_HOST='0.0.0.0' | ||
+ | |||
+ | # Object to listen on (DECnet): | ||
+ | # ROARD_OBJECT='roar' | ||
+ | |||
+ | # Annouce us via OpenSLP: | ||
+ | # Set to YES or NO. | ||
+ | # In case of YES roarclients can autolocat this server | ||
+ | # on the network. | ||
+ | ROARD_SLP='NO' | ||
+ | |||
+ | # --- [ EsounD Emulation ] --- | ||
+ | |||
+ | # Listen socket for server side EsounD emulation:: | ||
+ | # NONE - Disable EsounD emulation | ||
+ | # UNIX - Local connections only | ||
+ | # TCP - Connections via TCP/IP | ||
+ | ROARD_EMUL_ESD_AF='TCP' | ||
+ | |||
+ | # --- [ Audio and Devices ] --- | ||
+ | |||
+ | # Samplerate, number of channels and bits per sample: | ||
+ | # ROARD_RATE=44100 | ||
+ | # ROARD_CHANNELS=2 | ||
+ | # ROARD_BITS=16 | ||
+ | |||
+ | # Sound Driver and Device: | ||
+ | # To get a list run: roard --list-driver | ||
+ | # Don't forget to include 'sync' in the options unless | ||
+ | # you REALLY, REALLY know what you are doing | ||
+ | # ROARD_DRIVER='oss' | ||
+ | # ROARD_DEVICE='/dev/dsp' | ||
+ | # ROARD_DRIVER_OPTIONS='sync' | ||
+ | |||
+ | # --- [ Permitions ] --- | ||
+ | |||
+ | # User and Group to run roard with: | ||
+ | # Note: Users in the same group my access roard | ||
+ | # if runnung in UNIX mode. | ||
+ | ROARD_USER='roard' | ||
+ | ROARD_GROUP='audio' | ||
+ | |||
+ | # --- [ Security ] --- | ||
+ | |||
+ | # Directory to chroot to: | ||
+ | # Use empty value to disable. | ||
+ | # Directory may/should be completly empty. | ||
+ | ROARD_CHROOT='/var/empty' | ||
+ | |||
+ | #ll | ||
+ | </pre> | ||
+ | |||
=== /etc/default/rpld === | === /etc/default/rpld === | ||
=== /etc/ld.so.conf.d/roaraudio.conf === | === /etc/ld.so.conf.d/roaraudio.conf === |
Version vom 18. Dezember 2009, 16:45 Uhr
RoaringBox verwendet folgende Konfigurationen:
Gemeinsam
/etc/mini-httpd.conf
/etc/default/mini-httpd
/etc/default/roaraudio
#RoarAudio Configuration # --- [ General Options ]--- # Start roard? YES or NO: ROARD='YES' # Additionl Options to pass to roard, should normally be empty ROARD_OPTS='--new-sock -u -b /tmp/roar' # Should we run roard in realtime mode: # NO - Don't run in realtime mode # YES - Run in realtime mode # DOUBLE - Try to run in a 'very realtime mode' ROARD_REALTIME='YES' # PIDFile for roard: # Default is enabled at /var/run/roard.pid # Set to empty string to disable. PIDFILE='/var/run/roard.pid' # Location of roard: # This is a human readable location of the roard used # for Zero Conf locating of a RoarAudio server on the # Network. To use Zero Conf enable SLP (see below). #ROARD_LOCATION='' # Default location for roard: # Set this to a remote address and disable local roard # to run a network only setup. # ROARAUDIO_DEFAULT_SOCKET='server.local' # --- [ Network ] --- # Listening socket's address family: # UNIX - Local connections only # TCP - Connections via TCP/IP # DECnet - Connections via DECnet ROARD_AF='TCP' # Socket to listen on (UNIX): #ROARD_SOCKET='/tmp/roar' # Port to listen on (TCP): # ROARD_PORT=16002 # Host/Nodename to listen on (TCP, DECnet): # use a value of '0.0.0.0' to listen publicly for TCP. ROARD_HOST='0.0.0.0' # Object to listen on (DECnet): # ROARD_OBJECT='roar' # Annouce us via OpenSLP: # Set to YES or NO. # In case of YES roarclients can autolocat this server # on the network. ROARD_SLP='NO' # --- [ EsounD Emulation ] --- # Listen socket for server side EsounD emulation:: # NONE - Disable EsounD emulation # UNIX - Local connections only # TCP - Connections via TCP/IP ROARD_EMUL_ESD_AF='TCP' # --- [ Audio and Devices ] --- # Samplerate, number of channels and bits per sample: # ROARD_RATE=44100 # ROARD_CHANNELS=2 # ROARD_BITS=16 # Sound Driver and Device: # To get a list run: roard --list-driver # Don't forget to include 'sync' in the options unless # you REALLY, REALLY know what you are doing # ROARD_DRIVER='oss' # ROARD_DEVICE='/dev/dsp' # ROARD_DRIVER_OPTIONS='sync' # --- [ Permitions ] --- # User and Group to run roard with: # Note: Users in the same group my access roard # if runnung in UNIX mode. ROARD_USER='roard' ROARD_GROUP='audio' # --- [ Security ] --- # Directory to chroot to: # Use empty value to disable. # Directory may/should be completly empty. ROARD_CHROOT='/var/empty' #ll
/etc/default/rpld
/etc/ld.so.conf.d/roaraudio.conf
/etc/romie.conf
RoaringBox 128/*
RoaringBox 512/*
Siehe Auch
UUGRN-Wiki verbessern („Stub”)
Dieser Artikel ist leider sehr kurz. Also: Sei mutig und mache aus ihm bitte einen guten Artikel, wenn du mehr zum Thema „RoaringBox/Konfiguration” weißt.